Tensión

230/400V/D/Y, 50Hz (estándar para motores de hasta 3,0 kW)
Posibles aplicaciones: En conexión estrella (Y) directamente sobre red de 400V, en conexión triángulo (D) sobre convertidores de frecuencia con tensión de salida 230V/3~ o sobre convertidores de frecuencia con tensión de salida 400V/3~ y funcionamiento con curva característica 87Hz

400/690V/D/Y, 50Hz (estándar para motores a partir de 4,0kW)
Posibles aplicaciones: En conexión triángulo directamente en la red de 400V, y en convertidores de frecuencia con tensión de salida 400V/3~, arranque estrella-triángulo con interruptores o contactores

500V, 50Hz
El devanado está diseñado para motores de hasta 4,0kW en 290/500V/D/Y, 50Hz como estándar y a partir de 5,5kW en 500/865V/D/Y 50Hz.

Grado de protección

Código IP del grado de protección según DIN EN 60529, 60034-5,
Primer número de código: Protección contra la entrada de cuerpos extraños
Segundo número de código: Protección contra la entrada de agua con efectos nocivos

Opciones seleccionables:

IP55 - protegido contra el polvo, protección contra chorros de agua (estándar)
IP56 - estanco al polvo, protección contra fuertes chorros de agua
IP65 - estanco al polvo, protección contra chorros de agua
IP66 - estanco al polvo, protección contra chorros de agua potentes

Motor protection

The following options are available for monitoring the winding temperature of the motor:

• 1 set (3 pcs.) of PTC thermistors - for monitoring with PTC thermistor tripping device or
  Frequency inverter (standard)
• 1 set (3 pcs.) of temperature switches (bimetal NC contacts) - for monitoring e.g. with
  motor protection relay

Current carrying capacity
Rated current (AC: Cos Phi = 1.0): 250VAC / 2.5A
500VAC / 0.75A
Rated current (AC: Cos Phi = 0.6): 250VAC / 1.60A
500VAC / 0.5A

• Resistance temperature sensor PT100 - PT100 is a platinum resistance thermometer, which at
  0°C has a defined resistance value of 100Ohm and is used for precise temperature measurement.
• Resistance temperature sensor PT1000 - PT100 is a platinum resistance thermometer that has a defined resistance value of
  0°C has a defined resistance value of 1000 ohms and is used for precise temperature measurement.

The selection of one of these options is recommended when operating the motor on the frequency inverter, as the motor may overheat at reduced speeds and the associated lower cooling capacity.

Bearing

Locating bearing n-side
Motors up to size 132 have floating bearings on both sides as standard. Optionally, a fixed bearing can be selected on the n-side to absorb axial forces.

Reinforced bearing
From size 160, a reinforced bearing with NU bearings can be used on the output side (d-side). This is recommended for increased lateral forces, such as those caused by belt drives. The bearing must be relubricated regularly, either manually or using a relubrication device. Open NU bearings are used.

Relubrication device d- and n-side
Possible from size 160, for simple relubrication of the motor bearings. The relubrication device is standard from size 315.

Insulated bearing n-end for frequency converter operation
Measure to prevent bearing currents during operation on the frequency inverter possible from size 250.

Colour scheme

Colour shade

Standard colour RAL7024 - Graphite grey

Attachments and accessories

Fan cover with protective roof
Designed to prevent foreign objects from falling into the fan and to protect against water ingress. Used for motors with vertical installation position.

Forced cooling fan
For use with speed-controlled drives. The forced cooling fan installed in place of the standard fan cowl ensures sufficient cooling even at "very low" speeds. Multi-connection voltages: 230V/50Hz/1~ and 400V/50Hz/3~, protection class IP55
Attention - overall length of the motor increases!

Standstill heating
Prevents condensation even under extreme climatic conditions
Possible from size 80. Connection voltage: 230V/50Hz

Design/regulations

CE/UKCA (standard) - Mark of conformity that confirms that a product fulfils the applicable safety, health and environmental requirements of the EU or the United Kingdom.

UL/CSA version with combined certificate - Version with combined approval/certificate that complies with both US and Canadian regulations.

CCC version - The China Compulsory Certification (CCC) is a certification system valid in the People's Republic of China.

CEL labelling - Similar to the EU energy label, the China Energy Label (CEL) is a label for the energy consumption of a product. The label contains information on the energy efficiency class (1 to 5) and energy consumption.