Zkrácení dodací lhůty

Při zadávání objednávky se zjišťuje dostupnost komponentů potřebných pro konečný výrobek a možnosti výroby. Po potvrzení je za příplatek možná expresní výroba ve zkrácené dodací lhůtě.

Housing design

The following housing versions are available:

1. 1.A - push-on version, mounting with rubber buffer is recommended (see components)

1. 2.B - Push-on version - as A, plus bolt circle with threaded holes on both sides of the gearbox output

1. 3.C - Flange version C - for mounting the gearbox on the side output flange

Dimensions: see dimension sheet

Installation position

The installation position is required to determine the lubricant quantity.

The designations for the various installation positions can be found in the following illustration.

Shaft design

1 outer ring
2 Clamping screws
3 Inner ring
4 Hub
5 Shaft
6 Grease-free

Additional housing and shaft options

Double seal on the output shaft:

Depending on the available installation space, a combination seal with one NBR and FKM sealing lip each or two sealing rings in NBR and FKM design are used.

Advantages:

• - Optimum sealing properties at high operating temperatures thanks to FKM seal

• - Good sealing properties at low temperatures due to NBR seal

• - Better protection against high levels of soiling thanks to 2 seals (the outer seal also has a dust lip)

• - High level of safety and improved stability against oil leaks thanks to additional sealing lip

Use is recommended for

• - Critical installation positions

• - Where there are special requirements for the reliability of the seal

Reinforced bearing of the output shaft

With this option, the permissible radial forces for the output shaft can be increased.

Further information on determining the radial force and the permissible values for

standard and reinforced bearings in the PDF document Notes on selecting options

Rubber buffer for housing

Selection for slip-on version A. For elastic mounting (torque support) of the geared motor. Suitable for the hole on the front of the gearbox housing.

Mounting kit for hollow shaft

for mounting "customer shafts" with and without collar.

Further information in the PDF document Notes on selecting options

Protective cover for hollow shaft

Only possible with slip-on version B and flange version C. Fastening on existing threaded holes on the gearbox output.

Second shaft end

Standard version - without

Second shaft end - cylindrical shaft with keyway

Dust and water protection

Selectable options:

IP55 - dustproof, protection against water jets (standard)

IP65 - dust-tight, protection against water jets

IP65 with brake - as before, but with additional brake version in IP65

IP code for the degree of protection in accordance with DIN EN 60529, 60034-5,

First code number: Protection against ingress of foreign bodies

Second code number: Protection against ingress of water with harmful effects

Voltage/frequency

Selectable options:

230/400V/D/Y, 50Hz (standard)
Possible applications: In star connection (Y) directly on 400V mains, in delta connection (D) on frequency inverters with output voltage 230V/3~ or on frequency inverters with output voltage 400V/3~ and operation with 87Hz characteristic curve

400/690V/D/Y, 50Hz
Possible applications: In delta connection directly on the 400V mains, and on frequency converters with output voltage 400V/3~, star-delta start-up with switches or contactors

230/400V/D/Y, 50Hz // 460V/Y, 60Hz

290/500V/D/Y, 50Hz (up to 4kW possible)

500V/D, 50Hz (from 5.5 to 45kW possible)

Motor protection

The following options are available for monitoring the winding temperature of the motor:

a) 1 set of PTC thermistors - for monitoring with PTC thermistor tripping device or frequency inverter

b) 1 set of temperature switches (bimetal) - for monitoring e.g. with motor protection relay

The selection of one of these options is recommended when operating the geared motor on the frequency inverter, as reduced speeds and the associated lower cooling capacity can cause the motor to overheat.

Brake

The available brake types with max. possible braking torques are displayed for selection.

The following additional information is required to specify the brake:

Brake voltage

a) 230V/50Hz/1~

b) 400V/50Hz/3~

c) 24V (DC)

Braking torque at the drive motor (multiplication by the transmission ratio i results in the braking torque at the output shaft),

Manual release for the mechanical release of the brake via a lever, e.g. for adjustment or maintenance

Further information and technical data on the brakes can be found in the PDF document Notes on selecting options

Kleurnuance

Andere kleuren zijn beschikbaar op aanvraag voor grotere hoeveelheden.

Smeermiddel

De volgende smeermiddelen kunnen als optie worden geselecteerd:

0 Omgevingstemperatuur

1) Belastbaarheid O=normaal, +=hoog, ++=zeer hoog

2) Verouderingsbestendigheid O=normaal, +=hoog, ++=zeer hoog

Als optie 2 is geselecteerd, moet ook beschermingsklasse IP65 worden geselecteerd!

Ontluchtingsventiel

Voor het ontluchten van de versnellingsbak. Ontlast de afdichtringen en voorkomt lekken.

Standaarduitvoering vanaf versnellingsbakmaat F3.

Ventilatorkap met beschermkap

Bij verticale installatie voorkomt de kap het binnendringen van vreemde voorwerpen of vloeistoffen.
binnendringen van vreemde voorwerpen of vloeistoffen.

Condensafvoeropening
Afhankelijk van de installatiepositie van de motor bevinden de condenswatergaten zich aan de onderkant van de motor.
van de motor. De condensafvoergaten zijn in de fabriek gesloten en moeten worden geopend om condens af te voeren.
condensaat af te voeren.

Externe aardaansluiting

Tweede typeplaatje, los meegeleverd

UL/CSA-versie, met gecombineerd certificaat

Versie met gecombineerd goedkeuring/certificaat die voldoet aan zowel de Amerikaanse als Canadese regelgeving.
voorschriften

CEL-etikettering
Net als het EU-energielabel is het China Energy Label (CEL) een label voor het energieverbruik van een product.
energieverbruik van een product. Het label bevat informatie over de energie-efficiëntieklasse (1 tot 5) en het
energieverbruik. Het label is beschikbaar voor motorreductoren van 0,75 tot 45 kW.

CCC-versie
De China Compulsory Certification (CCC) is een certificeringssysteem dat geldig is in de Volksrepubliek China.
Het certificaat is beschikbaar voor motorreductoren van 0,12 tot 1,1 kW.